A difficult door is sometimes enough to journey you batty. And also the problem is there space a many reasons girlfriend may have actually a door the sticks.

You are watching: How to fix a sticky door

In this post, I’ll cover the four main reasons that may result in a door that sticks and also how to fix each them so you have a smooth swinging door that’s a satisfied to operate.

What kind of expensive and facility tools will certainly you require for this project? you won’t have to invest greatly for this one. If you have a screwdriver you’re practically there. If you desire to use a drill or influence driver the will always make things easier, however it’s not necessary. Check out the brief tool perform below:

tools Needed: ScrewdriverCircular experienced or orbital SanderStraight EdgeToothpicksWood GluePetroleum Jelly

Issue #1 Sagging Hinges

When the hinge screws come loosened any door will start to sag. And it’s commonly the top most hinge the comes loose because it carries the best load. Take it a look at your hinges and see if they have actually come loose from the door or indigenous the jamb.

The hinges should be securely fastened come both the door and the jamb and also if they can move even a tiny then they room too loose and must be tightened.

Step #1 remove the loose Screws

Place a block the wood, a book, a wadded up towel, or anything else you have handy choose your spouse or complain teenager under the latch next of the door to keep it sturdy while you remove any screws that have come loose. If the screws space stripped or stubborn then examine out my article 4 guaranteed Trick to remove Stubborn Screws.

Step #2 to fill the Screw Holes


*
Insert toothpicks into screw hole

Fill those screw holes v a little wood glue (you don’t require a ton) and some toothpicks. Yes, really you have the right to use any tiny piece of hardwood that fits in the screw hole but a few toothpicks usually perform the trick. Push the toothpicks every the way back and also break off any pieces that stick out so they room flush v the surface of the wood.

Step #3 Reinstall the Screws

With the screw hole smaller sized than it was and the adhesive in over there to assist everything continue to be put, the screw will find a much better grip to assistance your door. Tighten the screws down but don’t over-tighten them. Climate close the door to provide it a chance for the adhesive to dry and also lock things into place. Make sure to wipe off any kind of excess glue the squeezed out.

Other Considerations

There space a couple of things that might go wrong v this setup that you will want to consider. First, friend may find a stripped screw in your hinges i beg your pardon would have to be replaced. Over there is no quantity of glue and toothpicks that deserve to resolve a stripped screw.


*
Wood screw through tapered head

Another potential concern is the the wrong dimension or length screws were supplied before. If the screws aren’t long sufficient to really dig right into the timber then the will proceed to sag. Most hinges are installed with #8 lumber screws through a tapered head which must leave the head the the screw flush through the surface ar of the hinge when completely installed. If her screws recess greatly into the hinge or was standing proud the the hinge surface ar then you may have actually the wrong dimension or kind of screw.

Also, size is important. You require a screw the is long sufficient to support the weight of girlfriend door. 1 1/4″ is a an excellent choice, but for a particularly heavy door a much longer screw will certainly provide much more holding power.

Issue #2 Rubbing

If you live in an old residence then there is frequently some changing that has arisen over the years, or together in my home a kitchen remodel v a brand-new floor installed.

This results in a door the sticks as is rubs its means over the floor, threshold, or ~ above the jamb. If it’s a threshold worry then sanding one old wood threshold is simple solution. Otherwise, you’ll have to take the door turn off the hinges and also trim the bottom or political parties every therefore slightly.

If girlfriend only have actually a small rubbing then grab the orbital sander and also take a small meat off the section of the door the rubs. If it’s an ext extensive than that you have the right to use a one saw favor I carry out in the video clip below.


Step #1 eliminate the Door

Pop the hinge pins the end or unscrew the hinges and take the door the end of the opening. Ns love making use of a spring collection for acquisition hinge pins out. It’s so much less complicated than any type of other tool I’ve used. It’s ideal to have actually a pair saw equines setup through a towel on castle to avoid marring the door and set it on lock gently.

Step #2 Trim or Sand the Bottom

Using an orbital sander, sand the bottom the the door under or if you have to take off a more far-ranging amount of timber use a circular saw with a directly edge prefer the Kreg AccuCut Jig which is what i used.

Step #3 Reinstall the Door

Hang the door earlier in the opening and also test the fit. If you’ve got a smooth procedure with no an ext sticking or rubbing then you are done. If it requirements a little more tuning put it back on the witnessed horses and also make the necessary adjustments.

Other Considerations

If you have actually a move on the bottom the the door you might simply need to readjust that because that a better fit. If it’s not the move that is rubbing then taking the move off, trimming the door, and reinstalling the move is the method to go.

Some of this sweeps are very adjustable and others just fit one method so take a look at the type you have and also see if there is a way to change it to achieve a better fit.

Issue # 3 repaint Blocking

Another reason you’ll acquire a door the sticks is dubbed paint blocking. Repaint blocking is a wonderfully frustrating phenomenon the occurs once two painted surfaces space pressed together and they stick. That didn’t supplied to be a huge issue ago when oil-based paints were the norm, but with today’s water-based paints human being it wake up frequently.

Using harder enamel paints will help resolve this and you can read mine post around the repaint blocking test i did a while back to view the outcomes I come up with.

The best way to solve this is come repaint your door and also jamb v a high high quality enamel paint that won’t rod in the future, but if repainting is not in the cards right currently then over there is a super straightforward fix I’ll present you ideal now.

Step # 1 Lubricate the Edges

The key area you’re came to with right here are the edges of the door that push up again the jamb once closed. That’s whereby you obtain paint prevent that cause a door that sticks.

Using a clean cloth and also some soapy water, wipe this sections clean of any type of dirt or grime. After ~ it has dried, dip her finger in some petroleum jelly and also rub the onto the perimeter that the jamb in the little section the the door presses up against when closed.

You can likewise use part beeswax if you’d prefer. You simply need something to avoid having actually the two painted surface touch and also therefore stick.

Test the results and apply much more or much less as needed. You don’t desire to have actually globs the the stuff, for this reason be wise with it since you’ll it is in leaving that on permanently. If it gets dirty in time it have the right to be clear all off and also reapplied as needed.

Issue # 4 difficult Hardware

That last major reason you’ll gain a sticking door is the hardware. Periodically it’s faulty or damaged hardware which there isn’t much you have the right to do various other than change the hardware, but often it’s simple tweaks to obtain it to run smoothly.

Fix #1 – Proud Screws

More frequently than no I discover the worry is that hardware isn’t inside wall up properly and that reasons friction and a door that sticks. Open up your door and inspect the screws to make sure none of them are standing proud the the strike key or lock mortise. The screws must be totally flush through the surface.

Fix #2 – Misaligned Parts

Next check the alignment of the strike plate through the latch. If you check out scrapes whereby the latch connects come the strike key indicating that they don’t line up perfectly then the easiest resolve is to change the strike bowl so the the latch or deadbolt travels straight in the center of the hole when involved rather 보다 rubbing top top the to win plate and causing the sticking feeling.

Fix # 3 – Rusted Parts

Sometimes, especially in coastal areas, the inner functions of the door lock rust or gain dirt collected inside. The best method to resolve this is to take it the lockset out and also open it increase to research the parts.

See more: Piercings: How To Prevent Nose Piercing Infections, How To Clean Nose Piercing Safely

Don’t start taking every little thing apart. Progressively examine the parts and spray part rust resolver like Rust relax WD-40 or various other lubricants favor DryLube to try to get things working again. Test the function and reapply as necessary and also then once you gain the duty you want put it all back together and also reinstall the lockset.

Conclusion

The bottom line is that a difficult door is no something that the mean DIYer can’t fix. Usage these tips to troubleshoot your doors, and also hopefully you’ll be free of yet one more door the sticks. Good luck!