A lazy Susan is really just three pieces: a base, a top and also a ball bearing swivel in between. But, location it in the center of your dining table and it becomes a focal point at every meal. Here"s a perfect spot to showcase a special item of wood you"ve to be saving. For the project shown here, we"ll use a scrap that two-toned curly maple together an inlay medallion and also cherry for the other components. You could choose any species of lumber you prefer. You"ll likewise need a 12-in. Lazy Susan bearing, black color aniline dye powder and quick setting two-part epoxy. Here"s how to do this lazy Susan.

You are watching: How to make a tabletop lazy susan

Step 1: glue up a 3/4-in.-thick empty for the top and a 1/2-in.-thick blank for the base. We"ll make the last size of the height 14 1/2 in. And the basic 13 in. Leave the blanks oversized because that now. Mark the centerpoint top top both faces of the top blank with a scratch awl for this reason it will be straightforward to find after machining and also sanding. Mark the centerpoint that the base together well.

*

Step 2: pick the stock you"ll usage for the inlay medallion, and aircraft it down to 1/4 in. Thick. Identify the size of the inlay circle you want on her project, and also use a compass to draw the shape. Cut it round. Sand the edges as required to smooth them and to filter the circle. Our medallion actions 5-3/4 in.

Step 3: We"ll rout the recess because that the medallion, its black border and the stripe near the sheet of the top. In this case we offered a circle cutter to rout the recesses. Friend could additionally use a little router outfitted with a trammel. Drill a shallow, 1/8-in.-dia. Centerpoint for the one cutter"s pivot pin in the top blank. Drill a 2nd stopped hole to serve as a starter hole because that the router bit. Position this feet so that is inner leaf marks the sheet of your inlay"s diameter. By using a 1/8-in.-diameter router bit, the circle you"ll rout in the next step will become 1/4 in. Bigger than the inlay.

*

Step 4: download a circle cutter, lock it come the correct cutting diameter and collection the little depth come 1/8 in. Rout the external edge the the inlay area, rotating the tool carefully roughly the pivot point.

*

Step 5: Reset the circle cutter come mill a groove because that the external inlaid stripe. We collection this diameter in ~ 13-1/2 in. Do this circular groove 1/8 in. Deep as well. Once you"re finished, remove the circle cutter.

Step 6: switch to a 1/4-in.-diameter straight bit, set the cutting depth to 1/4 in. And also rout out the waste native the medallion area. To do this, begin in the center and feed the tool clockwise in an enlarging concentric circle, removing the rubbish slowly and carefully. Punch or brush away the debris as you occupational to monitor your progress. Avoid routing once you reach the inner sheet of the groove you made in action 4. The goal here is to leave a small rabbet that will assist center the inlay in the recess and type a shallower pocket for the inlay"s black color border.

Step 7: Glue and clamp inlay right into place. To help distribute the clamping pressure evenly, ar a larger piece of scrap end the inlay to act as a caul, and also apply clamps all approximately it.

*

Step 8: The inlay"s black border and also the interval stripe room made by mixing a tiny amount the aniline dye power with two-part epoxy. The exact ratio that epoxy to dye powder isn"t critical, but aim for about a 4-to-1 mix of epoxy come dye. Mix this "liquid" inlay in a shallow cup, and also fill the recesses through a putty knife or paint scraper. Scrape far the excess before it sets, and allow the epoxy come cure overnight.

Step 9: Plane, scrape or sand the top blank smooth come clean up the inlay stripes and also flatten the surface ar of the lazy Susan.

Step 10: usage the centerpoints the both blanks to attract the top and base to shape with a compass. Reduced out both circles and sand the edge smooth.

Step 11: Rout an leaf profile about the top, if girlfriend like. We made ours v a 3/8-in.-dia. Cove bit in a router. Ease the continuing to be edges of the top and base through a 1/8-in.-dia. Roundover bit.

Step 12: usage a compass to lightly draw circles top top the top and base for centering the swivel hardware, follow to the instructions that come v it. Bore a 3/4-in.-dia. Access hole through the base because that driving screws v the swivel and also into the top; this additionally will be explained in the hardware instructions. Drill pilot feet in the base and also top because that #8 x 1/2 in. Environment screws now.

Step 13: Sand the top and also base up v the grits to 180 and also apply your an option of finish. A heat- and moisture-resistant complete such as varnish is a great choice because that this project.

See more: How To Get More Matches On Bumble ? Why And What To Do Now 10 Bumble Hacks For Guys

*

Step 14: mountain the bearing hardware come the base through panhead screws.

*

Step 15: mountain the base assembly come the peak with screws, control them through the access hole in the base

Step 16: apply adhesive-backed feel tabs to your lazy Susan base. Now it"s prepared for tabletop display — and years of great use!